Develop Bugs

Universal dead after failed upgrade

First, I would like to thank everyone on this forum for valuable information. I have been able to flash a Blue Angel and more recently a Universal (SPV M5000) with a Jasjar, O2 and Qtek ROM.
I have researched the forum but have not found any answer close to my problem.
After the lastest update (O2 Exec just released), I did not reset the unit properly and now my screen is completely dead/blank. I tried to reflash but it is no longer recognized (will not power back up)
No possibility in putting in Boot loader mode (power+light+reset) or doing a hard reset (the 2 _ and reset).
has anyone experienced this and can I revive it, at least, bring it back to a boot loader so I can reflash? Thank you to all :roll:

Just a thought. Have you tried leaving out the battery pack for a while, say an hour or better overnight? Might be worth trying the hard-reset sequence with the battery still out, then insert the battery and hard-reset again. If it responds, try flashing again.
It is possible to get the Universal in a totally confused state. Mine does this everytime if I power down the workstation *without* first disconnecting the Exec from the USB-Sync cable. Fortunately, it will respond after a battery out plus reset, then battery in plus soft-reset, so I don't actually have to clear the memory.
Hope you dig yourself out of the brown stuff!

i am trying this at the moment as I do not know what else to do. I will put the battery back tomorrow in hope it will restart again.
Thank you for the advice

i am trying this at the moment as I do not know what else to do. I will put the battery back tomorrow in hope it will restart again.
Thank you for the advice

claudef said:
i am trying this at the moment as I do not know what else to do. I will put the battery back tomorrow in hope it will restart again.
Thank you for the advice
Click to expand...
Click to collapse
No to do that , connect ypur ppc to pc amd flush again after finish just push reset buttom , you will be ok, otherwide try one more time

Unfortunately, I cannot flash because it will not power up or start the boot loader. The pc does not recognize the device

claudef said:
i am trying this at the moment as I do not know what else to do. I will put the battery back tomorrow in hope it will restart again.
Click to expand...
Click to collapse
That worked for my when I was flashing my JAM, no problems. Scary, but successful. Think I may have left it a couple of days, to be sure. I then reflashed it successfully.
Although I refused to flash my Exec - too damned expensive to replace, and the ROM is 95% as good as it needs to be.

EXEC STUCK ON [SEE PICTURE] SCREEN NOT BOOTLOADER

hi all,
i was updating my rom on the exec & it all went well..
afteer the screen on my exec said 100% done, i followed the instructions on the pc screen, disconnected the usb & hard reset the ecec... after that when i switched the exec on.. it gets stuck on the following screen......
[/img]
i have tried flashing it again...it flashes, goes through the entire procedure and then same screen..
any help will be reallllly appreciated..
thanx
fzr

anybody????

the pictures are really blur so dont think anyone will be able to make anything out of it... Try taking the pics again in a dark room without the flash or if u can type down whats on the sceen!!!!!!! :roll:

this is exactly how the screen looks...
i can see the rom details radio details
thats all

you should be able to solve your problem after reading these threads
http://forum.xda-developers.com/viewtopic.php?t=59832
http://forum.xda-developers.com/viewtopic.php?t=43592

>to frz.
me too.
I flush 1.13x ROM then see that screen(same as frz uploaded).
but my EXEC work fine 1.30x ROM.(I tried O2 and QTEK's latest ROM)
I think bootloader v2.01 is not good.

i've just managed to sort it out
yes i've just managed to sort it out..
i think the O2 rom on the ftp is currupted
i downloaded the t-mobile rom & charged the battrey on someone elses exec...
made sure it is 100% charged
then i used manupgrade.exe & updated only the rom
no extended rom
no radia
after that reset
& thats it
it started working...
all the best

hx2410 stuck at boot screen

Hi! I have recently flashed my hp ipaq hx2410 to wm2005, the update process went fine but the device doesn't boot anymore. It shows the loading bar and it gets stuck when it fills up. I have tried hard reseting it but the problem persists. I can't flash it because active sync doesn't "see" it anymore... just a local area connection X - limited or no conectivity. What can I do ? Is there a way to boot the device in some sort of flash mode or something? Thank you very much

I had to do hard reset about 3 times when upgrading my hx2490B.
f1xxx3r said:
Hi! I have recently flashed my hp ipaq hx2410 to wm2005, the update process went fine but the device doesn't boot anymore. It shows the loading bar and it gets stuck when it fills up. I have tried hard reseting it but the problem persists. I can't flash it because active sync doesn't "see" it anymore... just a local area connection X - limited or no conectivity. What can I do ? Is there a way to boot the device in some sort of flash mode or something? Thank you very much
Click to expand...
Click to collapse

I have done a lot of hard resets but the device still gets stuck.
Another thing... I did not hard reset the device before de WM05 rom update. I thought it should do that by itself.
And second... If I get it to work I want to flash it to WM06. I have the rom but are there some special steps to be followed for this update ?
My pda still gets stuck in the bootloader and then the backlight turns off. Should I leave it that way untill the battery is completely flat ?

Some people say that removing the battery for 24 hours may help.
Try that.
When i flashed my 2490 i did format the device and than did the flash.
But I don't think that matters cause the first time when i did flash i didn't format the drive and it was OK.
f1xxx3r said:
I have done a lot of hard resets but the device still gets stuck.
Another thing... I did not hard reset the device before de WM05 rom update. I thought it should do that by itself.
And second... If I get it to work I want to flash it to WM06. I have the rom but are there some special steps to be followed for this update ?
My pda still gets stuck in the bootloader and then the backlight turns off. Should I leave it that way untill the battery is completely flat ?
Click to expand...
Click to collapse

I'll remove the battery then and see tommorow. The main question is: is my device completely dead or is it "resurectable" ? I don't think that it need servicing .... but ... just asking
Thank you for the replies. If the batterry removal fix works I'll post here. In the meantime any other possible sollutions are welcome.

My pda still doesn't boot. I have removed the battery for 24 hours and nothing. I have drained the battery and nothing. Did numerous hard resets and still no result. Can anyone help me ?

Just an idea (since I had to do this yesterday) maybe try formatting the device.
After flashing 4PDA ROM to my device it would get stack on the same screen as yours. After formatting it all went OK and I had WM6.
For my device I had to click calender + power + messaging + reset, release reset - release all.
f1xxx3r said:
My pda still doesn't boot. I have removed the battery for 24 hours and nothing. I have drained the battery and nothing. Did numerous hard resets and still no result. Can anyone help me ?
Click to expand...
Click to collapse

It's still dead....
It's back. P.S. Format did the trick

Same problem
i have " HP IPAQ hx2410 " with WM2003 CE 1.10.0 and i upgraded with this window 5.2 it upgraded successfully but i m stuck on the first loading screen. its stuck when loading complete i have tried every thing such as boot-loader thing and also cant downgrade it . . . so kindly plzzz any one tell me how can i go to my initial state on wm2003 ASAP.

WHAT IS P.S. Format ??? and how can i do that . . .

The answer is here:
http://tinyurl.com/2d4cza7

Diamond Shuts Down By Itself

hey, I'm only 1.40 Olinex unsigned;
when i first boot up I have this:
R 52.2.25.12h
G 1.00.25.05
D 1.93.0.0.0
My phone shuts down by itself, after i see the HTC logo and i hear the shut down sound.
why is that happening, is it software or hardware?
PS: RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship
I am flashing with this ROM, and with some other ROMs it is not even booting up

try this mate
try running mtty then reflash your rom, mtty formats your nand chip and repairs any erroes read THE DEFFINATIVE MTTY THREAD all explained there got to be worth a try hope this helps

trying this now will report on results thank you mate

still having problems, now phone wont boot up at all
i think i can make it boot
(I got USB error after i pressed <- and Vol Down to flash ROM )
is there a problem in my SPL? is my phone bricked?

i can boot into WinMo after i have left the phone for a few hours
but now 5-20 minutes after booting (depending on each time), suddenly i see the HTC logo, and here the shut down beep
any help ?

could it be a bad battery issue?
because when i turn it on i see an exclamation mark next to the battery icon in the bar on top
any suggestions? plzplzplz !!

MTTY Thread
Reflash your phone doing EXACTLY what it says in that thread and you should be good to go.

mzaouar said:
could it be a bad battery issue?
because when i turn it on i see an exclamation mark next to the battery icon in the bar on top
any suggestions? plzplzplz !!
Click to expand...
Click to collapse
Buy another battery, It looks like battery problem.
Good luck

now the battery looks like it's working fine, i've flashed a new radio ROM, but it's getting turned off again :S
should i upgrade to the 1.93 HSPL? because i have a 1.93 ROM
can the problem be from the radio?

Same thing here,
Been flashing the diamond to the bone.
After flashing the (22 jul) verion of the NRG warhawk rom
I have been experiencing some glitches.
As it was my first step from wm 6.1 to 6.5 and I dont want to go back.
The errors ive experienced are not related to rom issues.
Because i got em almost with every rom.
- random restarts
- loss of contacts
- no responding of the device
And ive been reading about the MTTY sollution I go and try that one.

Enonoid, so you didnt find a soltuion to your problem?
and if not, what do you suspect the culprit is?

Been flashing the diamond to the bone.
After flashing the (22 jul) verion of the NRG warhawk rom
I have been experiencing some glitches.
As it was my first step from wm 6.1 to 6.5 and I dont want to go back.
The errors ive experienced are not related to rom issues.
Because i got em almost with every rom.
- random restarts
- loss of contacts
- no responding of the device
And ive been reading about the MTTY sollution I go and try that one.
Reply With Quote
the problem isn't rom related running MTTY formats the chip where the rom resides its like reloading windows on your computer when you know there are bad sectors on your hard drive. it just wont happen follow the THE DEFINATIVE MTTY THREAD and honestly all should be fine it sounds quite tricky at first, but I use mtty everytime i reflash now saves whishing you'd done it once you've reinstalled everything and believe me its so easy if you just follow the guide.

Dead AQ4501

Nearly At the end of every month my my phone gets into some kinda software problem (example : Google has stopped working then process.android has stopped working and some other random **** which is quite annoying) whenever this happens the phone restarts on its own and never turns on,i mean it does but is stuck on loading screen.(note: I dont do anything stupid which might harm my phone. )So i have to flash my phone with spflashtool it.This time when i flashed the phone it didnt turn, i held the button for long but it was of no use, so i thought it might be the low on battery,but when i put it on charge nothing popped up... it wasnt charging. Then I thought it was the battery but my battery wasnt swollen and the day before I flashed it,it was running fine with full charge. , there was no sign of battery problem anytime i used it the consumption was normal.
Please help me fix this problem, and I also want a permanent fix to the software problem too.
Any senior member please help..
TIA
:fingers-crossed:
Update:I flashed the phone with new files but results were the same :'(

Saad6459 said:
Nearly At the end of every month my my phone gets into some kinda software problem (example : Google has stopped working then process.android has stopped working and some other random **** which is quite annoying) whenever this happens the phone restarts on its own and never turns on,i mean it does but is stuck on loading screen.(note: I dont do anything stupid which might harm my phone. )So i have to flash my phone with spflashtool it.This time when i flashed the phone it didnt turn, i held the button for long but it was of no use, so i thought it might be the low on battery,but when i put it on charge nothing popped up... it wasnt charging. Then I thought it was the battery but my battery wasnt swollen and the day before I flashed it,it was running fine with full charge. , there was no sign of battery problem anytime i used it the consumption was normal.
Please help me fix this problem, and I also want a permanent fix to the software problem too.
Any senior member please help..
TIA
:fingers-crossed:
Update:I flashed the phone with new files but results were the same :'(
Click to expand...
Click to collapse
same happens to me bro my android one is also dead same problem as yours when i tried with sp flash tool its end up with this error..... scr shot attached

☹
Bro,I flashed it thrice after but it didn't give any errors,but sadly it just wont turn on
If it were permanently bricked then it wouldn't have detected the phone...and bro lemme give you a suggestion,try changing it to firmware upgrade instead of download only.
Thanks for the reply

simmilar issue
same problem pls help in my case when i charge not charging the battery indicator just pops up and out i think its a battery error put in a new battery try to boot up nothing try to go in recovery nothing i have nothing to boot up from i think ill still try using fastboot and/or flashing and reporting back(ima try dead usb flash using spflash tool)

okay flashing works perfectly now i just need for figure out if the problem is with the charging/battery or the phone is dead

Same Problem
Bro, i have run into exact same problem. I even went to gallery and gave them the phone, they said they will charge 1500 as motherboard is dead but after one month they returned to me the phone saying that motherboard is not available. They are taking almost 14 days to return money so i have to visit again on 3rd june. But coming back to problem i have tried flasing with and without battery for 3-4 times. every times it shows success but the phone wont start. Even memory test was all fine. cant figure out what's the problem. i have tried both download only and format+download mode but nothing seems to work, If anyone finds a way to fix the phone please tell ASAP.

Same problem as the OP, mine's bricked as well after it began showing random FCs. Flashed KK and LP firmwares using SP Flash Tool but to no avail. The flash was successful tho but the phone never booted up

I'm kinda stuck in a similar situation. Let's start from the beginning -
When I got my Redmi Note 3 I stopped using my Canvas A1 and vaguely i remember that it was having software issues, rather than fixing it I just kept it away for a lot of months, and vaguely I remember that it just needed some flashing of rom and it would've gotten fixed.
And after all these months i'm need of this phone again. I don't remember much in depth details of the processes involved with it like flashing stuff etc. But I gathered as much knowledge as I could from the docs I had stored as backup & from the internet.
And IMO I think the flashing process was successful, but the screen is not turning on. Only once when I connected it to PC, the charging battery sign appeared(flashing thrice) but that was it. Nothing after that. And whenever I connect it to PC it detects the phone.
For now I've given it to a repair guy but I don't have much hope. He was saying that it could be just software problem, but I don't agree. If a smart person could comment on this thread so that we all could get some benefit out of it, in order to solve the situation or at least in my case I could research on something specific in the meantime.