Related
Hi, is it possible to connect the BA, via WIFI (P2P connection), to a PC with a WIFI card and use the PC's internet connection tu surf the web?
I tried: I can make the BA get the signal, but when I try to connect to a website it doesn't work.
Thank you in advance.
Bye.
fabbor75
I don't think its possible to do this directly using a P2P WIFI connection, but if you can get activesync to work over a P2P WIFI connection, it might work. I know is I use activesync over a USB connection & I can surf the net all day, so I'm thinking it might be possible to use the same approach over wifi.
Thing is I don't know if its possible to use activsync over P2P wifi
Solution
The problem is that windows not chain the IP Adrress of PC and Pocket bacause Nat not work under Xp basic system.
It's possible however to install a third party software to route packet from Pc to pocket i think all NAT's program can do that!!!!
Find one and Good Luck.
With WM2003SE i've used WINROUTE
Maybe?
Hi fabbor75!
Maybe your problem isn't the connection to the PC, it's maybe the DNS-resolution. Check your TCP/IP-settings on your BA, the important thing ar the DNS-Server.
The badest thing you must do is that you have to configure all TCP/IP setting manually: IP-Address, Subnetmask, Gateway and DNS-Server.
But you have to configure EXTERNAL DNS-Server on your BA, this one you got from your internet-provider, not the PC to which your BA is connected P2P. And the Gateway is the IP-Adress of your WiFi-card which is built-in in your PC.
Maybe this helps you.
Greetings, Peter
Can some one tell me how to share my 3G connection over wifi? I need to make the phone as a portable access point.
no can do.
Bluetooth or USB
Try hitchhiker it's free! but I'm not sure if it works for sharing using 3G... try it and let me know http://www.kasuei.com/hitchhiker/
No, It doesn't support to share the 3G connection.
So use Internet sharing over BT ?
Would like to use it as a wireless access point, so I can get access from computer and iPhone, seem like I have hard time to find a solution.
share the connection with the PC by USB. Put a wifi stick/pcicard in the PC and bridge the connections, then the iFoon can have 3G too
Maarten_NL said:
share the connection with the PC by USB. Put a wifi stick/pcicard in the PC and bridge the connections, then the iFoon can have 3G too
Click to expand...
Click to collapse
you got this to work?
or are you saying it should work?
i have tried to share a connection this way but have had no luck when using internet connection sharing/pan.
i did get it to work this way back in the day when the phone ran wm5 and had dun.
do you have any pointers on how to get internet connection sharing in wm6 to let more than one device connect to the 3g connection?
acem77 said:
you got this to work?
or are you saying it should work?
i have tried to share a connection this way but have had no luck when using internet connection sharing/pan.
i did get it to work this way back in the day when the phone ran wm5 and had dun.
do you have any pointers on how to get internet connection sharing in wm6 to let more than one device connect to the 3g connection?
Click to expand...
Click to collapse
seems like you may need an app on your pc to manage/route the connections not sure if this helps but you can try "network Magic" it give you a bit more options on the pc side for managing connections. would like to see where this goes for possible future applications. i'll give it a try when i have some free time and check with an comp tek friend of mine see what he thinks.
Yeah it sucks that no one has created a way to share the wifi connection just like we share bluetooth or usb.
We also need a proxy server that we can run on our phone.
ok, for me the boring part is the time of the connection, you can share via wifi by just turning on your internet sharing in whatever the pc connection, you just need to manually deffine your hermes wifi to 192.168.0.1 and it shares via internet sharing! The question here is that the connections stops after 10 minutes becouse of the warnig "check usb cable connection". Its very irritating to have to start connection every 10 min. !!!!!
awww...iPhones not fast enough Data-Wise for ya?
thought it was supposed to "revolutionize PDA Phones"
hah.
sorry, i had to add my 2¢ against Apple.
Beware, some mobile provider allready use NAT, thus you'll recieve a non-routable IP. I am not sure that you will be able to share a connection of this kind.
Hello,
I did a search and didnt find much, I also checked on Wiki and they explain how to use it as a modem via bluetooth dial up networking. I would like to use the bluetooth PAN feature in Internet Sharing but cant get it to work.
Firstly, I got the bluetooth dongle connected with the Bluetooth PAN. It tells me that they are connected and communicating with each other, the bluetooth software (bluesoleil) even provides me with an ip address, however when I try browsing on my laptop I get the message page cannot be displayed...
Can anyone please shed some light as to why it does not work?
Thanks a lot!
EDIT:
Seems like when the connection is established it gives the windows bluetooth adapter a weird ip address
like: 169.254.6.198
but I checked in network adapters of the 8525 everything is set for ip addresses to be assigned automatically .. strange..
in windows xp its also set to assign the ip address automatically :S
im not sure what else to do..
Launch Internet Sharing on your Hermes & set the PC connection to bleutooth PAN. Now, make sure the Network Connection is set to your correct data connectiion and press connect. It should say "Waiting for connection" Next, connect your PC & Internet Sharing should show "Connected". If you still can't surf then its a bluetooth driver issue on your PC. The built in M$ bluetooth stack (XP SP2 & >)works correctly with bluetooth PAN for sure. YMMV on others. The latest Toshiba BT stack definitely works too (based on pesonal experience).
Sleuth255 said:
Launch Internet Sharing on your Hermes & set the PC connection to bleutooth PAN. Now, make sure the Network Connection is set to your correct data connectiion and press connect. It should say "Waiting for connection" Next, connect your PC & Internet Sharing should show "Connected". If you still can't surf then its a bluetooth driver issue on your PC. The built in M$ bluetooth stack (XP SP2 & >)works correctly with bluetooth PAN for sure. YMMV on others. The latest Toshiba BT stack definitely works too (based on pesonal experience).
Click to expand...
Click to collapse
Hey,
Thats exactly what I did, and it gets connected on both ends..assigns a weird ip address.
I tried a few Roms, but now I am using urs the latest one dev 3.2
Always was a fan of your roms, but I cant get that bluetooth pan to work.
I also tried with WIDCOMM and Bluesoleil...
I get no where..
Anyone please??
Help!!
I guess I'll have to bump this thread to death in order to get some help !
man i had the same problem never got it figured out so if any one could help would be great
fb.knight said:
man i had the same problem never got it figured out so if any one could help would be great
Click to expand...
Click to collapse
Which bluetooth dongle you used...just curious?
Which chipset?
Ok, guys, got the problem resolved..it was the sucky bluetooth adapter from ebay "ISSC bluetooth adapter", piece of crap.. went to walmart got a usb 2.0 device for 25$ and all is well now.
Hi Guys,
either I dont know how to search or there is no info on VPN on the forum(I probably dont know how to search) In any case. I need assistance. How do I setup a VPN on my TyTn running WM6 and also how do I get remote desktop client? I am sure this was around previously. Did MS remove it from WM6? Or was it HTC? It this is the case.. how can one get it back?
thanks!
here's remote desktop. How do you use it? I don't know how to set it up.
thanks!!!!
now for VPN....
cheers!
The remote desktop client is available in several places in this forum for download.
To set up a VPN:
add a new VPN server connection
enter the name / ip of the server you want to connect to
select the vpn type -- ipsec or pptp
next
enter your user name and password
finish
The only way I have found to connect to the von is to goto
Start-Settings-connections-connections-edit my vpn servers- -- tap & hold MY VPN
select connect
you must be using a plan that assigns you a public IP (not WAP)
hope this helps
JTK said:
Hi Guys,
either I dont know how to search or there is no info on VPN on the forum(I probably dont know how to search) In any case. I need assistance. How do I setup a VPN on my TyTn running WM6 and also how do I get remote desktop client? I am sure this was around previously. Did MS remove it from WM6? Or was it HTC? It this is the case.. how can one get it back?
thanks!
Click to expand...
Click to collapse
Thanks cmccarter, done it but how will I know I am connected.. It does not say connected anywhere that I can see and when clicking/hold on the item it gives me the option to connect again, not disconnect as I would have thought The other thing is terminal server does not connect. It connects fine on USB. VPN/Remote desktop connects fine using normal internet on pc from outside the network. So I believe the network settings are fine.. How would I know though if I am on WAP or get an IP. Also ow would I know if the VPN is connected?
thanks
fyi
i also have struggled getting rdp to work over a vpn, in particular over 3+/hsdpa
the only i found in wm5 was to add the vpn connect to the exceptions list of the connection manager, so that it didnt disconnect the vpn whem connecting the rdp.
this occurs more when u use an ip address to connect to a work intranet.
suppose if u use the dns name of the machine and not the ip address then it isnt that much of an issue. in wm5 when u put the ip address in it assumes a an internet rather than intranet connection so it disconnects the vpn to look for the ip over the internet
putting the ip into exceptions forced wm5 to not disconnect it when rdp was looking for it.
i cudnt get it to work this way in wm6 so i am also looking for an answer on this.
rdp to my servers when they have crashed and i am on the road wud b wonderful....
Hi,
I've a similar problem.
I use a VPN-1 SecuRemote that normally connect my PC directly to the company network.
Well, using the share modem tool, I'm not able to reach the gateway.
the share modem system give me a private IP that establish a connection between PC and TYTN.
This connection use the Tytn like a gateway to navigate in internet.
Someone know to solve this issue?
Tanks a lot
if i select start the vpn connection, nothing happens - and i can`t ping the IP`s in the VPN. so i think the vpn ist not open - OR the routing entrie is missing....
is there some shiny "pptp - standalone" client?
greets, Nik
for some reason i dont think the vpn option works over 3g/hsdpa, atleast not on my device using t-mob web and walk.
if i connect the vpn when using wifi it connects and everything is fine, if i try and connect when i'm already running a 3g connection it doesn't work.
i dont think the radio stack is capible of handling a 3g connection and a vpn connection. we might need to go down the route of getting a seprate wm vpn client.
Hi,
I haven't managed to get BT internet sharing working between the TP2 and my laptop. I've been trying to create a BT personal area network that enables internet sharing. Whenever i select the internet sharing option, it claims my laptop doesn't support it.
This is bogus, because i had the same laptop with the same setup working just fine through my old Tytn II. You just enabled internet sharing and away you go! How HTC have managed to mess this up is baffling (and annoying!). Trouble is i need to route my laptop through my phone or it's not very useful.
Is there any way that is known to work?
Thanks for any ideas,
Don't know if this is feasible in your situation, but can't you just use the USB cable and ICS? Tethering through BT would be slower and less reliable than using the cable.
It is easy but I'm not sure if you aware about the new widcomm btooth settings applet. In the 3rd tab, select Networking Manager > Share Internet Connection > Follow On Screen > Done.
I am having the same problems and I have tried the network manager > share internet connection but no luck. what makes my case worse is that i have the Toshiba bluetooth stack. any ideas?
gotta try that with tp2 btw yesterday when i tried to send some files from tp2 to my old hermes (tytn) it didn't work because tp2 claims 'device does not support a suitable service to perform this operation'. however the bt-link between my lap-top and tp2 or tytn works fine and i have used the internet sharing many times with my old tytn
so maby the are some issues with the newer bt? dunno
Eureka! I have manged to get a connection and i am posting this over it. But I tried so many things that I am going to have to delete the connection and start all over again so I can create a step by step guide for anyone that may be intersted. Test enviroment is TP 2 WM 6.1 (obviously) and Toshiba laptop with Toshiba stack running Vista.
You have the same problem as i did if you will get the error msg 'remote device does not support bluetooth PAN' and have a toshiba bluetooth stack. I should be back soon. Wish me luck so I dont mess up everything.
1. Enable BT on TP2 and make device discoverable
2. On laptop right click BT icon --> options --> General --> select PAN networking service
--> yes --> ok.
3. On laptpp right click BT icon --> add new connection --> custom mode --> next --> select your TP2 --> next --> select group ad-hoc network --> next --> next --> finish.
4. On your device --> open ICS --> select bluetooth PAN --> select your PC from list of BT devices --> accept connection on PC.
You should be good to go at this stage cos it works for me. If you dont mind leaving the PAN networking icon on your taskbar then you only need to do step 1 and 4 anytime you want to share your internet connection otherwise it will be step 1, 2 and 4.
Good luck and I hope someone finds this useful. I also hope in the future there will be an easier and more straightforward way to connect. There probably is now but I just dont know it. Half bread they say is better than none. cheers
If the fix from lombardo8 does not work/apply to you - try the following:
1) Setup/ connect an ordinary BT serial port from your PC to the phone.
2) Use the Widcomm BT applet as monx suggested above to setup the rest.
I have found that I cannot initiate any BT activity from my phone to the PC without a connection made from the PC to the phone first - even though the PC and phone both use Broadcomm stacks!
Also my Tytn II worked perfectly with my PC so likely not to be a PC problem.
Hope this helps...
lombardo8 - you are the dude!
this worked! indeed, i too am running the toshiba BT stack. it's the one i found before worked. I had tried creating all sorts of new connections from the PC settings, but the difference you have found is in the BT options/general settings.
Strangely, the "select PAN networking service" box was not checked. i guess this explains why PAN networking wasnt active. however, what is strange is that this must have worked before using my old TyTn II without this setting.
So once this is enabled, it makes a connection fine!
with regard to wire tethering, this is always a handy fallback, but i have found that BT usually worked quite well, once set up and working, additionally you dont need a wire.
For the life of me i cannot get it to work with my work notebook running Win7 and my netbook running Win7 & OSX
It's driving me nuts
Why can't they just leave it simple. Damn Bluetooth 2.1
Is there any chance somebody can have a .cabs to install back the old internet sharing where there is a Bluetooth PAN in the drop down list. I figured that would be alot easier.
I had the same issues with TP2 and a Mac Book Pro. It works perfectly on Windows XP on this machine but not in OSX. I found a solution for OS X though:
http://forum.xda-developers.com/showpost.php?p=4101986
Thanks for the info but now i'm getting the error msg below
"Failed to establish Internet Sharing connection to remote devices as it supports only Network Access Point (NAP) mode"
What does that mean and how do i configure it in OSX?? Appreciate any help with this as i need ISC in OSX.
Well it means that TP2 thinks that your Macbook offers the internet sharing and not the TP2. I get that same message until i kill the blued and tick that mark again. Then it works until next reboot where i have to repeat the sequence again. Which OSX Version and hardware are you using btw?
Seems the new Snow Leopard fixes some issues with bluetooth. I re-paired my TP2 with Snow Leopard and this works like a charm out of the box. No more fiddling with the bluetooth daemon. Let's see if it stays that way
Just disable DHCP on laptop/PC PAN & u r ready to go.
Scann69 said:
Is there any chance somebody can have a .cabs to install back the old internet sharing where there is a Bluetooth PAN in the drop down list. I figured that would be alot easier.
Click to expand...
Click to collapse
Yes bro. v1.11 will have this feature but still Widcomm stack & bt PAN working 100%
Bluetooth ICS Windows 7 WinMo 6.5
I'd like to chime in here. I've flashed several 6.5 ROMs, but with the 23016 and 23017 sys roms I can't seem to connect bia BT ICS. The USB cable works fine. It seems that my netbook does not acquire an IP address from the TouchPro. I'd sure like to find a fix for this as I use this technology all the time.
@izzyforreal
see my post above. did u disabled dhcp on ur netbook bt pan profile?
monx® said:
@izzyforreal
see my post above. did u disabled dhcp on ur netbook bt pan profile?
Click to expand...
Click to collapse
Hi monx!
How do you disable DHCP on the PC's BT PAN profile? I'm using Widcomm/Broadcom firmware 2.1.211.299 by the way.
And if I do disable it, how will the PC get an IP address??
Thanks,
- Shay
skamin said:
Hi monx!
How do you disable DHCP on the PC's BT PAN profile? I'm using Widcomm/Broadcom firmware 2.1.211.299 by the way.
And if I do disable it, how will the PC get an IP address??
Thanks,
- Shay
Click to expand...
Click to collapse
I've found the solution here. Not using the "Internet Sharing" application though but a couple of nice hacks. IT ACTUALLY WORKS!!!
See attached ZIP with files and that post quoted.
- Shay