Alright.. This is a new one for me.
I have read almost all the threads on the incredible vibrating 3 and 5 times while booting on XDA and incredibleforum and tho the problems are similar they are not the same so I am unable to find a fix.
I have rooted the incredible , both the amoled and the SLCD version half a dozen times each and am pretty familiar with all aspects of it.
The setup...
Stock Dinc SLCD running latest OTA. totally 100% stock. This is my wifes phone, and she wanted me to root it.
I used Unrevoked 3.3.
The unrevoked process went perfectly. I plugged in the phone, hit "start" , unrevoked did its thing. It rebooted the phone, did what it does.. said "waiting for reboot", it rebooted fine. It said "this has been a triumph!" and then it said it was uninstalling unrevoked processes, then it rebooted the phone again. It did its hboot thing one more time, screen said "doing preboot sequence" it sat for a sec and then said "done!". The incredible vibrated 3 times and the screen was black.
I thought that was odd, I disconnected the USB cable and rebooted the phone (had to battery pull). when i pushed the power button it vibrated 3 times and nothing happened.
I pulled the battery again, held volume up and power , it vibrated 5 times and had a black screen. Battery pull, held optical button and power, vibrated 3 times and black screen.
This is where I sit.
I did nothing more than run unrevoked 3.3.. that is totally it.
when i "boot" the phone and get the 3 or 5 vibrations, and then plug the phone into the PC, the device manager says "qualcomm CDMA device" under unrecognized devices.
I have read that this is some sort of diagnostic mode, but I dont know anything about that.
Let the troubleshooting begin
msticlaru said:
Alright.. This is a new one for me.
I have read almost all the threads on the incredible vibrating 3 and 5 times while booting on XDA and incredibleforum and tho the problems are similar they are not the same so I am unable to find a fix.
I have rooted the incredible , both the amoled and the SLCD version half a dozen times each and am pretty familiar with all aspects of it.
The setup...
Stock Dinc SLCD running latest OTA. totally 100% stock. This is my wifes phone, and she wanted me to root it.
I used Unrevoked 3.3.
The unrevoked process went perfectly. I plugged in the phone, hit "start" , unrevoked did its thing. It rebooted the phone, did what it does.. said "waiting for reboot", it rebooted fine. It said "this has been a triumph!" and then it said it was uninstalling unrevoked processes, then it rebooted the phone again. It did its hboot thing one more time, screen said "doing preboot sequence" it sat for a sec and then said "done!". The incredible vibrated 3 times and the screen was black.
I thought that was odd, I disconnected the USB cable and rebooted the phone (had to battery pull). when i pushed the power button it vibrated 3 times and nothing happened.
I pulled the battery again, held volume up and power , it vibrated 5 times and had a black screen. Battery pull, held optical button and power, vibrated 3 times and black screen.
This is where I sit.
I did nothing more than run unrevoked 3.3.. that is totally it.
when i "boot" the phone and get the 3 or 5 vibrations, and then plug the phone into the PC, the device manager says "qualcomm CDMA device" under unrecognized devices.
I have read that this is some sort of diagnostic mode, but I dont know anything about that.
Let the troubleshooting begin
Click to expand...
Click to collapse
call for a refurb. I had it happen twice.
ACD168 said:
call for a refurb. I had it happen twice.
Click to expand...
Click to collapse
I have a refurb sitting next to me lol. I wanted to root the old one so that I could do a backup and then restore that backup on the new phone. Wife saves pictures and videos to the phones memory (i know) so i would like to recover this if possible.
Also, it seems like this is something that has to be recoverable. Some sort of software is telling it vibrate 3 or 5 times. I am still doing research on this
Well if you're trying to get into hboot you need to hold volume down and power, not volume up. Also not sure what trackpad+power does, I do know you can basically do the same thing as a battery pull by pressing volume down + power + trackpad. Have you tried booting the phone up normally too?
k_nivesout said:
Well if you're trying to get into hboot you need to hold volume down and power, not volume up. Also not sure what trackpad+power does, I do know you can basically do the same thing as a battery pull by pressing volume down + power + trackpad. Have you tried booting the phone up normally too?
Click to expand...
Click to collapse
For referance. I just 5vibed my last inc last week, i know all about it.
k_nivesout: oj + power boots fastboot
For the OP, your device is now in qualcomm diagnostic download mode. Hence qualcomm devices in device manager.
To date this is still a none recoverable issue. NO ONE has ever recovered from this.
Good news is if your still in warrenty VZW will send you out another one for free over night. Just call Tech support directly. Just tell them your phone vibed 3 times and shut off. They'll have you do some things to it over the phone. If what they have you try dosn't work, they'll send you one out over night.
Hope this helps a little and hopefully this will save you from countless hours researching. Took me three days, before I realized I had been beaten, lol.
k_nivesout said:
Well if you're trying to get into hboot you need to hold volume down and power, not volume up. Also not sure what trackpad+power does, I do know you can basically do the same thing as a battery pull by pressing volume down + power + trackpad. Have you tried booting the phone up normally too?
Click to expand...
Click to collapse
ive always used optical key plus power to boot into hboot, volume down and power works too, but ive alyays just used optical key (easier to press)
hwoever..
volume up + power - 3 vibrates
volume down + power - 5 vibrates
optical key + power - 3 vibrates
and power alone - 3 vibrates
with all of these, the screen is always black
When i plug in the phone after any of these scenarios, the PC recognizes it as Qualcomm CDMA device
msticlaru said:
ive always used optical key plus power to boot into hboot, volume down and power works too, but ive alyays just used optical key (easier to press)
hwoever..
volume up + power - 3 vibrates
volume down + power - 5 vibrates
optical key + power - 3 vibrates
and power alone - 3 vibrates
with all of these, the screen is always black
When i plug in the phone after any of these scenarios, the PC recognizes it as Qualcomm CDMA device
Click to expand...
Click to collapse
Wait, wait, wait just a minute. i wanna talk to you in private. check your pm
msticlaru said:
The 3 vibrate brick - Please Help {SOLVED}
Click to expand...
Click to collapse
Glad I could help you fix this. Don't forget to post what we did to solve this so others can learn from us
This is written for the HTC incredible, please ensure you get the proper ruu image for your particular phone. For example, the HTC wildfire will be PG76IMG.zip, not PB31IMG as I have written below. the rest of the steps are applicable to all HTC phones.
Click to expand...
Click to collapse
a BIG thanks to wildstang83 for this!
If you are getting vibrates when trying to boot your phone. do the following:
Download (see above comment)
build-3.26.605.1-release-152016-baseband-2.15.00.07.28-hboot-0.92.0000_PB31IMG.zip
google, you will find it.
backup your SD card, format it fat 32 and place this file on the root of your card. Be sure to rename it PB31IMG.zip
Once it is on your sd card, verify the MD5 to ensure the file was not corrupted during the download or during the transfer.
Hold Vol down + power. you will feel 5 vibrations
wait for a god 2 to 3 min. if everything is going correctly, your phone is verifying the IMG file and this takes a bit.
after 2 to 3 min. wait one more min
now, press vol up. this tells the phone to update.
wait 2 to 3 min for the update to happen then wait one more.
press vol up again. you should feel the phone single vibrate and then presto.. working phone again
next time be more careful
Please let me know if this did not work for you.
THANKS WILDSTANG!! You're what these forums are all about
Nicely done! I've never encountered this issue but I'm remembering this for future reference just in case.
Is that just the stock ROM? I had this problem a few months ago, unrooted through Hboot using the stock image placed onto the SD card.....it never fixed the issue though, the phone would still not recognize the SD card once booted but since I was unrooted I could at least return it.....
nate2830 said:
Is that just the stock ROM? I had this problem a few months ago, unrooted through Hboot using the stock image placed onto the SD card.....it never fixed the issue though, the phone would still not recognize the SD card once booted but since I was unrooted I could at least return it.....
Click to expand...
Click to collapse
Yes, this is the stock image method.
nate2830, your case is more typical because your phone was in full-blown Qualcomm Diagnostic Mode. Your device did this because you lost eMMC to corruption. OR you hade hardware failure.
The OP's device '3 Vibed' because when they had rooted with unrEVOked the wrong recovery for there device was installed.
A device with version 0002=Amoled must have CWM Recovery version 3.0.0.5
A device with version 0003=SLCD must have CWM Recovery version 3.0.0.8
If your device is not set-up like above, I highly suggest getting it there now.
Your device has a higher chance of "5 vibe" brick otherwise.
I am led to believe this is the case for our OP do to immediately after root (well actually during the root process if you will) they lost all screen function and the screen would not light. This meens of course: wrong recovery for the device. Also in there post above They had mentioned that Device Manager mentioned Qualcomm CDMA Device. Had there device been a total loss they would have seen Qualcomm CDMA Diag in Device Manager.
We were able to save the OP by doing what we call a 'Blind Recovery'. One must know the steps to take and how long to wait between those steps. Without being able to see the screen. Doing the dougpiston PB31IMG wipes the faulted recovery and reverts back to oem recovery which brings back phone screen function and the device it self.
End result being a device that
A) Functions properly that is now stock s-on ready to root again or whatever
B) Is now s-on with stock image and no trace of ever being rooted that now can be sent back to VZW for warranty replacement.
In any case, if you ever find yourself with a device with a screen that won't light, always try the steps above in this thread.
Things that are important to know:
1. Your devices Hardware version (Reference Above)
2. The md5 sum of ANYTHING your about to flash to your device. Test this after its on your SD Card with any md5 checker for best results.
3. If anything your about to download and flash does not have a posted md5 sum, ask the dev to please post one for verification.
4. A '5 vibe' is 'non-recoverable' and is generally 'hardware related'
5. A '3 vibe' is generally 'software related' and can be recoverable 'most' of the time. We must be careful how we proceed to take action to be succcessful.
I hope that the OP and I have saved someone from a future headache.
wildstang83 said:
Yes, this is the stock image method.
nate2830, your case is more typical because your phone was in full-blown Qualcomm Diagnostic Mode. Your device did this because you lost eMMC to corruption. OR you hade hardware failure.
The OP's device '3 Vibed' because when they had rooted with unrEVOked the wrong recovery for there device was installed.
A device with version 0002=Amoled must have CWM Recovery version 3.0.0.5
A device with version 0003=SLCD must have CWM Recovery version 3.0.0.8
If your device is not set-up like above, I highly suggest getting it there now.
Your device has a higher chance of "5 vibe" brick otherwise.
I am led to believe this is the case for our OP do to immediately after root (well actually during the root process if you will) they lost all screen function and the screen would not light. This meens of course: wrong recovery for the device. Also in there post above They had mentioned that Device Manager mentioned Qualcomm CDMA Device. Had there device been a total loss they would have seen Qualcomm CDMA Diag in Device Manager.
We were able to save the OP by doing what we call a 'Blind Recovery'. One must know the steps to take and how long to wait between those steps. Without being able to see the screen. Doing the dougpiston PB31IMG wipes the faulted recovery and reverts back to oem recovery which brings back phone screen function and the device it self.
End result being a device that
A) Functions properly that is now stock s-on ready to root again or whatever
B) Is now s-on with stock image and no trace of ever being rooted that now can be sent back to VZW for warranty replacement.
In any case, if you ever find yourself with a device with a screen that won't light, always try the steps above in this thread.
Things that are important to know:
1. Your devices Hardware version (Reference Above)
2. The md5 sum of ANYTHING your about to flash to your device. Test this after its on your SD Card with any md5 checker for best results.
3. If anything your about to download and flash does not have a posted md5 sum, ask the dev to please post one for verification.
4. A '5 vibe' is 'non-recoverable' and is generally 'hardware related'
5. A '3 vibe' is generally 'software related' and can be recoverable 'most' of the time. We must be careful how we proceed to take action to be succcessful.
I hope that the OP and I have saved someone from a future headache.
Click to expand...
Click to collapse
Oh sorry!! Thought it was a similar problem, but had a feeling it wasn't since the stock image didn't resolve my issue. Thanks!
My DINC was suffering from the 5 vibe syndrome. If I used it for anything that stressed the system or even used the phone for a few minutes it would result in a reboot that ended with a black screen, 5 vibes, and the indicator flashing green. At first I could pull the battery for a few minutes and it would recover. Eventually I ended up putting it in the freezer for a bit to get it running again. This progressively got worse until it was nearly unusable. Then I stumbled upon this thread..
http://forum.xda-developers.com/showthread.php?t=982454
Turns out mine was a hardware failure as the processor's BGA grid was failing. I heated the processor and now have a fully functional DINC. I had nothing to lose by trying this as I bought it second hand and didn't want a fancy paperweight on my desk.
Thanks guys, for helping me out with a 3-vibe brick i just had for no reason at the gym today. Was listening to music, texting, working out. All of a sudden, music stops, phone completely unresponsive. Battery out, 30-second wait, restart gives me boot-screen boot loops. Volume up + power gave me a 3 vibe brick.
Thanks to you guys, I discovered that i could get into hboot, boot into recovery from there, do a full wipe, reflash of CM7.0.3 and get the phone to start again. However, that's when the next BIG PROBLEM started. Screen went to sleep while restoring apps from the Market and now when i press the power button, the soft buttons light up but the screen doesn't. This is just super-duper to have problems like this on the same day I was telling a friend that I wouldn't trade this phone for anything else VZ has right now. Anyone have any advice?
PS - The only thing I did today besides "normal" use, is i updated Handcent and changed the LED flash rate.
msticlaru said:
a BIG thanks to wildstang83 for this!
If you are getting vibrates when trying to boot your phone. do the following:
Download
build-3.26.605.1-release-152016-baseband-2.15.00.07.28-hboot-0.92.0000_PB31IMG.zip
google, you will find it.
backup your SD card, format it fat 32 and place this file on the root of your card. Be sure to rename it PB31IMG.zip
Once it is on your sd card, verify the MD5 to ensure the file was not corrupted during the download or during the transfer.
Hold Vol down + power. you will feel 5 vibrations
wait for a god 2 to 3 min. if everything is going correctly, your phone is verifying the IMG file and this takes a bit.
after 2 to 3 min. wait one more min
now, press vol up. this tells the phone to update.
wait 2 to 3 min for the update to happen then wait one more.
press vol up again. you should feel the phone single vibrate and then presto.. working phone again
next time be more careful
Please let me know if this did not work for you.
THANKS WILDSTANG!! You're what these forums are all about
Click to expand...
Click to collapse
Sounds good, I'm hearing a RUU will work just as well?
This got my phone to turn on, but now im in a boot loop. How could i fix this? I appreciate all the help.
I actually recovered from a 5 vibrate error. I had flashed the leaked GB over a stock sense without doing a wipe and got stuck in a boot loop. Every time I tried to either power up into hboot or recovery (- vol and power, or + vol and power) I would get 5 vibrations and then a blank screen. If I tried to power up normally nothing but boot loop after the white htc screen. So I just kept trying to get hboot to load and then after about 5 tries it worked and I was able to get into recovery and flash a backup ROM. I still have problems getting hboot to load properly and it appears its a problem with how hard I press the volume keys. If I press it too hard I get five vibrations followed by the blank screen and it still takes a number of tried to get it to work right. Getting into recovery from ROM Manager is no problem it works flawlessly and I can flash ROMs with it no problem, just have problems when I manually try it. Otherwise the phone works great.
Well if you're doing volume up and power I believe that puts it into a diagnostic mode where it vibrates three times (I think) and flashes the led. Also, I'm not sure how the pressure with which you press the button would matter, I'd think it either recognizes the button press or doesn't.
k_nivesout said:
Well if you're doing volume up and power I believe that puts it into a diagnostic mode where it vibrates three times (I think) and flashes the led. Also, I'm not sure how the pressure with which you press the button would matter, I'd think it either recognizes the button press or doesn't.
Click to expand...
Click to collapse
Like I said it does it with the - volume and power combination too, + volume and power used to go straight into recovery bypassing hboot.
Its not so much the amount of pressure but the length of time I press the buttons, if I hold them too long I get the 5 vibrates, if I press them both then quickly relase them the phone will usually boot normally into hboot but not always. The button psuhing could all be coincidence and the phone just randomly works right after so many tries so I don't want to mess with the phone too much as I'm sure that eventually it will stop responding at all some day. I've never had problems flashing through ROM Manager so I will just use this and skip trying to do anything manually.
OK.
I will put in a detailed info about what happened.
A week back, my wildfire's touchscreen started to function abnormally.
I was rooted and on Cyanogenmod 7.0.3
So, I flashed the phone with DK custom FROYO to make it look like sense so that the warranty is not void and took it to the HTC store.
They replaced the touchscreen for a flat fee (It was water damage according to them. But the phone was never used in wet conditions nor exposed to water)
But anyway, the phone was working fine when I brought it home from their store.
Then I flashed CM7.0.3 again.
And everything was working fine.
I OCed acc. to CM's settings to 652-352 Mhz.
And left the phone to charge in charger overnight.
When I woke up, the phone was off and there was just the red LED light blinking.
I tried to boot it again, but nothing works.
Pressing the power button does not do anything.
The phone still boots into recovery. At times.
I don't know what makes it boot into recovery. But at times it does, at times it doesn't. (Right now it's not booting into recovery no matter what I do)
Just the red LED keeps on blinking.
Please help.
I am not familiar with pushing commands onto the wildfire since I use a mac.
Please suggest any methods. If they involve using command line, I can use my windows PC for that. But please give a how-to of length enough for a noob ) ) to understand.
Thank you.
Pulz
EDIT :
I got to boot into recovery once. Tried to reflash CM7.0.3
It came to "Installing update" and then failed to go further.
Tried to install DK Custom Froyo 4.5
And it went to opening package and then failed to go further.
Now entering into a panic mode !
Red light blinking generally occurs when phone is hot and plugged in to wall socket. Is it so at that time ?
Unplug the charger or usb. Remove the battery and reinstall the battery. Try to boot into hboot mode (volume down + power) or fastboot mode (trackpad + power) . If your phone can boot into hboot/fastboot mode and has no restarts or power offs, then I think you can solve it.
Try to clear storage from hboot menu. Or factory reset from recovery once you enter it. If still it is not solved, try using "pc49img" method of flashing an RUU from the hboot menu. Hope it helps. Shouldn't help if there is hardware issue.
Sent from my Blade using XDA App
hye another noob here running on cm7.
actually i have the similiar problem my wildfire start rebooting over and over again but the cause is different.
this problem happen after i want to know what class my micro sd is.
what i do is i go to settings>storage>unmount sd card.
so after knowing the class were i insert back the card then the problem happens.
my phone start to crash then cm7 logo appear after that i enter my pin no so brought me back to the home screen after few seconds the logo appear again so i have 2 repeat the same steps...
this happen many times what i do is i remove the battery wait few hours then turn back on..
so help me if someone have the similiar problem and solutions.. thanks!!
Hey guys
I'm running MrGarak's fantastic MIUI rom however I've found that the kernel is booting my phone into that white HTC diagnostic screen by default. Unfortunately my volume down button is dead and so I can't navigate the menu; the only way I can boot my phone at the moment is to boot it connected via USB as that makes it boot to Recovery and I can reboot from there.
Any ideas? I think this and another rom I tried both used LordMUE's kernel, could that be the reason the boot preferences don't default to just booting the OS?
Any help and/or pointers would be greatly appreciated
So you can access bootloader and recovery!
So just flash another kernel. What's your problem?
Put a zip on your SD (with a SD reader or ADB pull), then go in recovery, navigate with the 4 keys under the screen (or vol+ and power)... and flash.
What is strange for me is that it seems to happen sudenly... so how do ou know it's the kernel. Anyway...
I have clockwork recovery, and can navigate it using the soft keys (home menu etc). You should also he able to use the vol up key to get to the bottom of the list, (depending on the recovery you're using I suppose)
Sent from my Desire HD using Tapatalk
_david_94 said:
I have clockwork recovery, and can navigate it using the soft keys (home menu etc). You should also he able to use the vol up key to get to the bottom of the list, (depending on the recovery you're using I suppose)
Sent from my Desire HD using Tapatalk
Click to expand...
Click to collapse
Unfortunately it boots into the white HTC area (dunno what it's called). The one where you can see if your phone is S-OFF or not.
Also, I'm not sure what is to blame... but I've only just recently noticed that my phone cold boots this way so I assumed it was a recent rom that I applied. Will test this theory later.
Sounds to me like your volume down button is stuck in.
Definitely not a ROM issue, as it has nothing to do with the bootloader.
Sent from The App that Time Forgot.
Hey, i had this issue like a month ago. You can check my previous threads. It's hardware I'm 100% sure. Basically if you're in warranty you need to flash the stock rom with S-On so you can get a new phone. You can get it to boot but it's really a pain. You have to play with the volume up when first turning on your phone. It took me about an hour. Then when it boots you'll be in a "Safe Mode" (no clue whats limited all seemed fine to me). Then do your backup if you wish.
Also note: Flashing the S-On rom is a PAIN, took me about 2-3 hours of rebooting, holding vol up, tapping vol up, to get it to boot right, but with patients you'll get it to go.
Good luck to ya.
xtremedelta said:
Hey, i had this issue like a month ago. You can check my previous threads. It's hardware I'm 100% sure. Basically if you're in warranty you need to flash the stock rom with S-On so you can get a new phone. You can get it to boot but it's really a pain. You have to play with the volume up when first turning on your phone. It took me about an hour. Then when it boots you'll be in a "Safe Mode" (no clue whats limited all seemed fine to me). Then do your backup if you wish.
Also note: Flashing the S-On rom is a PAIN, took me about 2-3 hours of rebooting, holding vol up, tapping vol up, to get it to boot right, but with patients you'll get it to go.
Good luck to ya.
Click to expand...
Click to collapse
Ah, I'm definitely beyond warranty. The thought of vol+down being stuck down makes a lot of sense!
I'll just take it to one of the dodgy Asian repair shops, if it's a hardware issue I'm sure they'll know what to do.
Cheers for your help everyone!
Hello everyone! So I've had my phone (HTC One M8) rooted and custom recovery and rom installed for a little while now. The latest rom I've installed was Android Revolution HD 22.1. I also have twrp 2.8.1.0 installed. The other day my phone got wet and started to constantly reboot itself, wouldn't shut off and stay off, would never actually start. I put it in a cup of rice for 2 days, then proceeded to plug it in to charge it. Once charged enough I tried to turn it on. It only made it the HTC One logo screen and would vibrate every 10 seconds or so. I tried rebooting several times and no matter what I did with different button combinations I could not get it to load into bootloader. Eventually with restarting different ways and "mechanically stressing" the phone (short temper lol) I managed to get it to loading into the rom itself. From there I opened hasoons all in one toolkit to reboot directly into recovery and recovered to the stock rom. So the phone will now reboot with no problem into this rom. I haven't tried reflashing the ARHD 22.1 rom again because im afraid it'll break again. However, while in the stock rom everything work fines except for the volume up button which does nothing, except for while the screen is off, if I turn my phone to landscape the camera app will open without me even pressing the volume up button. If I reboot into bootloader via the quickboot app or hasoons toolkit, my volume down button with make the cursor go up, the volume up button does nothing, and the power button does nothing. The only thing I can do in bootloader is to hold power+volume up to get the phone to reboot. I also cannot get bootloader to load by holding volume down+power. So, After all that explaining, my main question would be, do you think that the buttons are shorting in a weird way because of water damage, or do you think my software got corrupted because of all the rebooting it did? Any help is appreciated, thanks!
-Tim
(PS: I posted this in XDA assist originally but figured it would be better being posted here.)
UPDATE: my power button will now lock my phone but not unlock it.